The SSDTH Weatherboard Screw and Quik Drive® Auto-Feed Screw Driving Systems are a stronger and faster fixing method for timber cladding to timber framing requires a clean and less noticeable finish.
The DWP Softwood-to-Softwood screw is a powerful fastening solution for decking and general exterior applications where extra corrosion protection is required.
The Deck-Drive™ DSV Softwood-to-Softwood screw is a powerful fastening solution for preservative-treated decking applications.
The Strong‑Drive® SDS Heavy Duty Connector Screw is a 6.4mm diameter structural wood screw ideal for various connector installations as well as timber-to-timber applications.
The CCN64 Collated Connector Nailer helps to ensure the correct installation of connectors through its unique design and is considerably faster than traditional hand nailing.
The ESCR screw has a washer head and 6 lobe drive to aid installation and give excellent pull-through capacities.
The ESCRC is a countersunk head screw designed to connect two or more timber members together. The countersunk head gives flush fitting while allowing the timber members to close up firmly.
The ESCRFTC is a countersunk head screw with a fully threaded design to connect two or more timber members together. The countersunk head gives flush fitting while allowing the timber members to close up firmly.
The Strong‑Drive® SDWC Truss Screw provides a truss and rafter-to-top plate connection as well as a method to fasten stud-to-top and bottom plate.
The Strong‑Drive® SDWS is the 2nd generation structural screw, redesigned with a patented SawTooth™ Point.
The PT-27 Powder-Actuated Tool is engineered for continuous use, high reliability and low maintenance. This versatile tool installs both standard and washered pins in various lengths.
Simpson Strong‑Tie offers a wide variety of holdown devices designed and tested to address many applications and load demands. The DTT Tension Tie & Holdown is designed for lighter‑duty holdown applications on single or double studs.
The SP4 Stud Plate Tie is a versatile solution for connecting the stud to the top and bottom wall plates. The SP4 wraps around the plate, requires no nailing into the plate and is suitable for single bottom plates and double top plates.
Joist hangers are designed to provide support underneath the joist, rafter or beam to provide a strong a connection. The LUS Double Shear Joist Hanger values engineering at its finest. All hangers in the LUS series have Double-Shear Nailing.
The CS Coiled Strap provides nail slots for easy installation. It can be used on the wide or narrow face of timber for light repairs or heavy-duty projects.
To provide more consistent, straight corners, Simpson Strong-Tie offers a wide variety of angles in various sizes and thicknesses to handle light-duty jobs or projects where a structural connection is needed.
Hurricane Ties provide a positive connection between the truss/rafter and the wall of the structure to resist wind and seismic forces. These ties connect both solid-sawn and engineered timber across a wide range of applications.
Simpson Strong‑Tie offers a wide variety of holdown devices engineered and tested to perform and manufactured to the highest quality standards.
Simpson Strong‑Tie offers a wide variety of holdown devices designed and tested to address many applications and load demands.
The IUC Face Fix Concealed Joist Hanger is a face‑mounted concealed flange hanger solid timber sections. Ideal for end of ledger/header or post conditions, the IUC also provides cleaner lines for exposed conditions such as overhead decks.
The IUSE Face Fix I-Joist Hanger is a hybrid hanger that incorporates the advantages of a face mount and top mount hanger. Installation is fast with the Strong‑Grip™ seat, easy‑to‑reach face nails and self‑jigging locator tabs.
The LSC Light Staircase Stinger Connector offers a versatile, concealed connection between the stair stringer and the carrying header or boundary joist while replacing costly framing.
The MASA Bottom Plate Anchor provides a time‑saving alternative to M12 and M16 cast‑in‑place anchor bolts on 45mm bottom plates.
The MP Mending Plate is a versatile and easy-to-use mending plate for timber-to-timber connections. No nails or notching of timber required. For non-structural applications only; not for truss applications.
The RR47 Ridge Rafter Connector provides a solid connection between rafter and ridge beam. The RR47 provides alignment control and correct nailing locations.
The SAE Face Fix Joist Hanger is a heavy-duty hanger designed for applications requiring additional strength.
The SDE Split Joist Hanger is a two‑piece, width‑adjustable joist hanger that can accommodate joist widths from 60mm and 120mm. Each SDE is comprised of one left and one right piece.
TJC is a versatile connector for jack trusses. Adjustable from 0 to 85 degree (shipped with 67.5 degree bend). Nail hole locations allow for easy installation.
The TP Tie Plate joins and reinforces joints with a simple, versatile solution for a wide range of connections. The TP is a nail-on tie plate, which is designed to be used back-to-back on a piece of timber without fastener interference.
The TSP Stud Plate Tie connects from one side and is suitable for single bottom plates and double top plates. The TSP adds strength and rigidity to the critical stud-plate connection.
The WBT Wall Brace Tensioner is an easy‑to‑use wall strap‑brace tensioner that takes the slack out of strap bracing, saving time over other methods.
The BA Top Fix I-Joist Hanger is designed to be used where a heavy load/connector is required. It is cost-effective and used for structural composite lumber and high-capacity I-joists.
The ABR255 is a hold down bracket designed for fixing CLT panels to concrete / timber floors and parapet walls. Very versatile, it is particularly resistant to shear loads thanks to its optimized geometry.
TFLS provides the combined function of levelling and fixing the sole plate to the foundation or substructure. It comprises a universal base plate and packing pieces which can be added or removed as required.
NPB255 nail plate has been developed specifically to fix CLT panels to timber or concrete.
For a concealed connection, the ETB concealed connector comes in two parts. The first is pocketed in the header timber and fixed with nails, while the second part is fitted to the end of the beam with screws.
The revolutionary screw connector attachment, QDBPC50E, for installing Simpson Strong-Tie® CE-labelled CSA connector screws.
The innovative design of the LSSR Slopeable & Skewable Joist Hanger allows it to adjust for skew up to 45° and features an innovative hinged swivel seat to adjust for up to a 45° slope on site, eliminating the need for pre‑skewed/sloped or cus
With nearly 60 years of field and R&D experience, Simpson Strong-Tie® timber connectors are manufactured to the industry's highest standards. From framing angles to straps to heavy-duty joist hangers, we offer the most diverse product line so that you have the right product for the job.
Simpson Strong-Tie® connectors offer unmatched quality with laboratory and field testing, and are backed by our uncompromising commitment to customer service. As the company that built the connector industry, you can count on Simpson Strong-Tie® to work closely with builders, engineers and building officials to deliver innovative, building code-compliant solutions to help build safer, stronger structures economically. Download the Timber Connectors NZS 3604 Catalogue.
From testing to service to availability, everything we do is engineered to ensure your project's success. With every product, you know you are getting the quality, value, service and on-time delivery that we have built our reputation on for the past 60 years.
From straps and ties to joist hangers and much more, Simpson Strong-Tie® structural connectors increase the strength and safety of timber-frame structures. Each connector is unique to Simpson Strong-Tie and is designed for specific applications without the need to adapt metal plating to suit a connection. Download the Timber Construction Connectors Catalogue.
Steel Frame Connectors
From fully tested and engineered connectors and clips Simpson Strong-Tie® provides comprehensive structural solutions for cold-formed steel construction. From steel-to-steel connections to full-scale lateral solutions and curtain wall connectors, we remain committed to developing new technology that helps to advance the cold-formed steel industry.
Find out how Simpson Strong-Tie timber connectors can help you build the right way every day. Download the Cold-Fromed Steel Construction Connectors Catalogue.